点击图片查看大图1 标准动平衡为G6.3/10000RPM，一般台湾产品为G6.3/8000RPM，动平衡效果更佳。
2 全系列动平衡校正，每一ER螺母均经校正（包括侧固式刀柄）。
3 刀柄中心出水和法兰出水设计，更适合欧洲机床配备。
4 内部抗拉强度为950N/mm2,淬火硬度为HRC60±2，淬硬层深度为0.8mm±2,表面通过发黑和精磨处理。
5 采用5轴车铣复合机，一次性加工完成，减少二次以上重复夹持误差。
6 耐用性很好，我司刀柄在使用一年后还可以保证同新刀柄同样的精度，台湾其它厂商的刀柄使用半年后基本上不能保证很好的跳动精度。
规格如下：
| SK30-ER16B-70H |
| SK30-ER16B-100H |
| SK30-ER16B-70 |
| SK30-ER16B-100 |
| SK30-ER20B-70H |
| SK30-ER20B-100H |
| SK30-ER20B-70 |
| SK30-ER20B-100 |
| SK30-ER25B-70 |
| SK30-ER25B-100 |
| SK30-ER32B-70 |
| SK30-ER32B-100 |
| SK30-ER40B-70 |
| SK40-ER16C-63H |
| SK40-ER16C-100H |
| SK40-ER16C-160H |
| SK40-ER16C-200H |
| SK40-ER16C-230H |
| SK40-ER16C-63 |
| SK40-ER16C-100 |
| SK40-ER16C-160 |
| SK40-ER16C-200 |
| SK40-ER16C-230 |
| SK40-ER20C-60H |
| SK40-ER20C-100H |
| SK40-ER20C-160H |
| SK40-ER20C-200H |
| SK40-ER20C-230H |
| SK40-ER20C-60 |
| SK40-ER20C-100 |
| SK40-ER20C-160 |
| SK40-ER20C-200 |
| SK40-ER20C-230 |
| SK40-ER25C-60 |
| SK40-ER25C-100 |
| SK40-ER25C-160 |
| SK40-ER25C-200 |
| SK40-ER25C-230 |
| SK40-ER32C-70 |
| SK40-ER32C-100 |
| SK40-ER32C-160 |
| SK40-ER32C-200 |
| SK40-ER32C-230 |
| SK40-ER40C-80 |
| SK40-ER40C-100 |
| SK40-ER40C-160 |
| SK40-ER40C-200 |
| SK50-ER16C-63H |
| SK50-ER16C-100H |
| SK50-ER16C-160H |
| SK50-ER16C-200H |
| SK50-ER16C-250H |
| SK50-ER16C-300H |
| SK50-ER16C-63 |
| SK50-ER16C-100 |
| SK50-ER16C-160 |
| SK50-ER16C-200 |
| SK50-ER16C-250 |
| SK50-ER16C-300 |
| SK50-ER20C-60H |
| SK50-ER20C-100H |
| SK50-ER20C-160H |
| SK50-ER20C-200H |
| SK50-ER20C-250H |
| SK50-ER20C-300H |
| SK50-ER20C-60 |
| SK50-ER20C-100 |
| SK50-ER20C-160 |
| SK50-ER20C-200 |
| SK50-ER20C-250 |
| SK50-ER20C-300 |
| SK50-ER25C-60 |
| SK50-ER25C-100 |
| SK50-ER25C-160 |
| SK50-ER25C-200 |
| SK50-ER25C-250 |
| SK50-ER25C-300 |
| SK50-ER32C-70 |
| SK50-ER32C-100 |
| SK50-ER32C-160 |
| SK50-ER32C-200 |
| SK50-ER32C-250 |
| SK50-ER32C-300 |
| SK50-ER40C-80 |
| SK50-ER40C-100 |
| SK50-ER40C-160 |
| SK50-ER40C-200 |
| SK50-ER40C-250 |
| SK50-ER40C-300 |
