点击图片查看大图| 品牌: | convoy |
| 型号: | CK1004 |
| 供电电源: | 220 |
| 通讯方式: | 烟雾通讯 |
| 继电器驱动: | 有 |
| 探头输入方式: | 接线电流 |
| 环境温度: | -10-50 |
| 环境湿度≤: | 95 |
| 外形尺寸: | 420x180x170 |
| 适用范围: | 家庭、控制室 |
| 类型: | 消防报警主机 |
| 颜色: | 红色 |
fire control panel 多线型火灾报警主机 消防报警主机 深圳厂家
The Panel is a 4-zone to 16-zone FACP (Fire Alarm Control Panel), which uses
conventional input devices. The panel accepts water flow devices, two-wire
smoke detectors, four-wire smoke detectors, pull stations and other
normally-open contact devices. Outputs include four Notification Appliance
Circuits (NAC, SOUND1-4), three standard Form-A relays (alarm, trouble and
supervisory) and an EIA-485 port to interface with remote annunciators and
optional remote relay modules. The FACP is field programmable via the panel
keypad. It also supervises all wiring, AC voltage and battery level.
This series of panels are basically the same in application and operation, their
differences are shown in Table 1-1. The Panel will be described as the example in
the following sections.
Table 1-1
FACP Number of
Detection Zones
Number of
Sounder Outputs
Output Delay
Settings
ZONE-4 4 1 N/A
ZONE-8 8 2 N/A
ZONE-16 16 4 N/A
1.1 Product Features
l 4,8,16 Class B Initiating Device Circuits (IDCs)
? All zones accept conventional detectors and any normally open
contact device
l Four Class B Notification Appliance Circuits (NACs)
l One Form-A Alarm Relay
l One Form-A Trouble Relay
l One Form-A Supervisory Relay
l 3.0 amps of system power
l Max 20 conventional detectors in one zone.
l Auto/Manual mode setting enable walk test.
l Each Zone can be disabled,
l Sound output can be disabled.
l Manual active sound output enabled.
AC Power
90 to 270 VAC, 50 /60 Hz, 2.3 amps
Wire size: minimum #14 AWG (2.0 mm2) with 600V insulation
Battery (lead acid only)
Maximum Charging Circuit: Normal Flat Charge—27.6V @ 0.8 amp
Maximum Charger Capacity: 18 Amp Hour batter
Sound Output Device Circuits
General Alarm Zones 1 through 16
Operation: All zones Class B
Normal Operating Voltage: Nominal 24 VDC (ripple = 100 mV maximum)
Alarm Current: 15 mA threshold
Short Circuit Current: 42 mA maximum
Maximum Loop Resistance: 100 ohms
End-of-Line Resistor: 4.7K, ½ watt
Detector Loop Current is sufficient to ensure operation of two alarmed detectors
per zone
Standby Current: 7.26 mA
Three Relays Output
Relay contact rating: 2.0 amps @ 30 VDC (resistive), 2.0 amps @ 30 VAC
(resistive)
Nonresettable 24 VDC Power
Maximum ripple voltage: 10 mVRMS Operating Voltage nominal 24 volts
Total DC current available from this output is up to 500 mA
Recommended maximum Standby current is 150 mA
1.4 Circuits
Input Circuits
Sixteen input circuits provide configuration. Input circuits 1 through 16
may be used as standard fire alarm control panel zones. All sixteen
Initiating Device Circuits accept normally-open contact devices and
two-wire smoke detectors.
Output Circuits
• 24 Volt Resettable Power Output 1000 mA
• 24 Volt Nonresettable Power Output 1000 mA
• 24 Volt Battery Charger (up to 18 AH batteries)
• EIA-485 Port (interfaces to Annunciators, and Graphic Annunciators
and Remote Relay Module)
Sound (Notification Appliance )Circuits
Four Notification Appliance Circuits.
Relays
Three dry relays for system alarm, system trouble and supervisory are
provided standard. Contacts are rated 2.0 amps @ 30 VDC (resistive) and
2.0 amps @ 30 VAC (resistive).
EIA-485 Port（Optional）
EIA-485 compatible port supports up to 10 different device addresses which
can consist of Remote Annunciators, Relay Modules, Annunciators or
Graphic Annunciators or any combination of the four modules.
Battery Charger
Battery Charger will charge up to 18 AH batteries. The PANEL cabinet
联系方式
联系电话
解先生：13410101800
孙小姐：18814452893
QQ：解先生：234745514
孙小姐：1060363721
传真号码：0755-29749366
阿里旺旺：cszss
官方网站：http://www.cszss.com
联系地址：深圳市宝安区福永宝安大道6267号世峰大厦907
