珠海飞宇光电洛个公科技有限公司

Here presents the generic specification for the 96 channel 50GHz Thermal AWG MUX/DEMUX component supplied by Flyin for use in DWDM system.

This product is designed for use within the C -band release of DWDM system. To decrease the power dissipation of the devices in different environmental conditions, the AWG package is special designed with selection of reliable thermal plastic with low thermal conduction, and the AWG operating temperature is controlled by using foil resist heater or Peltier TEC with thermistor temperature sensor. Different input and output fibers, such as SM fibers, MM fibers and PM fiber can be selected to meet different applications.

参数/Parameters

条件/Condition

规格/Specs

单位/Units

Min

Typ

Max

通道数/Number of Channels

96

通道间距/Number Channel Spacing

50GHz

50

GHz

中心波长/Cha. Center Wavelength

ITU频率/ITU frequency.

C -band

nm

通带频率/Clear Channel Passband

±6.25

GHz

波长精度/Wavelength Stability

Maximum range of the wavelength error  of all channels and temperatures in average polarization.

±0.05

nm

-1 dB 带宽/-1 dB Channel Bandwidth

Clear channel bandwidth defined by passband shape. For each channel

XX

nm

-3 dB 带宽/-3 dB Channel Bandwidth

Clear channel bandwidth defined by passband shape. For each channel

XX

nm

插损/Optical Insertion Loss at ITU grid

Defined as the minimum transmission at ITU wavelength for all channels. For each channel, at all temperatures and polarizations.

6.0

7.5

dB

相邻通道隔离度/Adjacent Channel Isolation

Insertion loss difference from the mean transmission at the ITU grid wavelength to the

highest power, all polarizations, within the ITU band of the adjacent channels.

25

dB

非相邻通道隔离度/Non-Adjacent, Channel Isolation

Insertion loss difference from the mean transmission at the ITU grid wavelength to the

highest power, all polarizations, within the ITU band of the nonadjacent channels.

30

dB

总隔离度/Total Channel Isolation

Total cumulative insertion loss difference from the mean transmission at the ITU grid wavelength to the highest power, all polarizations, within the ITU band of all other channels, including adjacent channels.

22

dB

插损一致性/Insertion Loss Uniformity

Maximum range of the insertion loss variation within ITU across all channels, polarizations and temperatures.

1.5

dB

方向性/Directivity(Mux Only)

Ratio of reflected power out of any channel(other than channel n)to power in from the input channel n

40

dB

插损平坦度/Insertion Loss Ripple

Any maxima and any minima of optical loss across ITU band, excluding boundary points, for each channel at each port

0.5

dB

回损/Optical Return loss

Input & output ports

40

dB

PDL/Polarization Dependent Loss in Clear Channel Band

Worst-case value measured in ITU band

0.3

0.5

dB

偏振模式色散/Polarization Mode Dispersion

0.5

ps

最大承受光功率/Maximum Optical Power

23

dBm

功率监控范围/MUX/DEMUX input/ output

Monitoring range

-35

+23

dBm

尺寸/Dimensions

428*251*43.7

mm

光纤类型/Fiber Type

公共端Common G657A fiber with 900mm loose tube，加900mm 套管，通道端G652DRibbons Channels

光纤编排/Fiber Format

4x 12带纤/4x12-fiber ribbons

光纤长度/Fiber Length

输入端/Common

1000mm ±50mmwith 900um loose tube/输入线长1000mm ±50mm带900um套管

输出端/Channels

Ribbon 500mm±20 mmand Fan out500mm±30mmwith 900um loose tube

/输出带纤500mm±20 mm，加分支器线长500mm±30mm

公共端/Common

颜色/Color

白/white

带纤标识/RibbonIdentification

带纤末端贴数码贴标识

/Label with ribbon number to be placed midway between ribbon end-points

连接器类型/Connector Options

Common

LC/UPC

Channels

LC/UPC

带纤光纤标识/Fiber Identification in Ribbon

1

蓝/Blue

2

橙/Orange

3

绿/Green

4

褐/Brown

5

灰/Grey

6

白/White

7

红/Red

8

黑/Black

9

黄/Yellow

10

紫/Purple

11

粉/Pink

12

水/Aqua

NO.

Parameters

Notes

Specifications

Units

Min

Typ

Max

2.23

Set-Point temperature of component

Optimum operating temperature section for thermal AWG

The commands could only set current temperature and threshold in this range.

65

90

°C

2.24

Set-Point temperature stability

Over entire operating temperature range for thermal AWG

±0.5

°C

2.25

Heater Drive Voltage

+5

V

2.26

Heater Drive Current

2.5

A

2.27

Heater Power Dissipation(maximum, stable)

12.5

W

2.28

Heater Power Dissipation(stable state)

25°C ambient temperature

6

W

2.29

AWG Temperature Settling Time

AWG warm up time from a cold start(25°Cambient temperature) to set point for thermal AWG

7

min

2.30

AWG Temperature Settling Time

AWG warm up time from a cold start(-5°Cambient temperature) to set point for thermal AWG

15

min

NO.

pin#

Signal Name

Type

Direction

Descriptions

2.31

1

+5V

Power

----

supply for Heater circuit

2.32

2

+5V

Power

----

supply for Heater circuit

2.33

3

+5V

Power

----

supply for control circuit

2.34

4

Ready

TTL

Output

※Set HIGH when the internal temperature is at a set-point temperature.

※Set LOW when the internal temperature is not at a set-point temperature (higher than the Upper Temperature Threshold or lower than the Under Temperature Threshold).

※This signal should be 3.3V TTL level.

2.35

5

Alarm

TTL

Output

※Set HIGH when the internal temperature is higher than the set-point temperature.

※Set LOW when the internal temperature is not higher than the set-point temperature.

Pin4 and pin5 could be used to check the temperature’s status.

※This signal should be 3.3V TTL level.

2.36

6

Enable

TTL

Input

※If set HIGH, the heater circuit is activated.

※If set LOW, the heater circuit is disabled.

※This signal should be 3.3V TTL level.

2.37

7*

TX

TTL

Output

RS232 transmit signal

This signal should be 3.3V TTL level.

2.38

8

GND

Power

----

Ground

2.39

9*

Rx

TTL

Input

RS232 receive signal

This signal should be 3.3V TTL level.

2.40

10

GND

Power

----

Ground

The planar DWDM components described within this datasheet are fully qualified according to Telcordia reliability assurance requirements for fiber optic and opto-electronic components (GR-1221-CORE/UNC, Generic Reliability Assurance Requirements for Fiber Optic Branching Components, and Telcordia TR-NWT-000468, Reliability Assurance Practices for Opto-electronic Devices). The reliability report is available for request.

AWG

X

XX

X

XXX

X

X

X

XX

Band

Number of Channels

Spacing

1st Channel

Filter Shape

Package

Fiber Length

In/Out Connector

C=C-Band

L=L-Band

D=C+L-Band

X=Customize

16=16-CH

32=32-CH

40=40-CH

48=48-CH

96=96-CH

XX=Special

1=100G

2=200G

5=50G

X=Special

C60=C60

H59=H59

C59=C59

H58=H58

XXX=special

G=Gaussian

B=Broad Gaussiar

F=Flat Top

M=Module

R=Rack

X=Special

1=0.5m

2=1m

3=1.5m

4=2m

5=2.5m

6=3m

S=Specify

0=None

1=FC/APC

2=FC/PC

3=SC/APC

4=SC/PC

5=LC/APC

6=LC/PC

7=ST/UPC

S=Specify