咸阳泰思特试验会商好啊设备有限公司

      PL6-C型纸样抄取器（快速凯塞法抄片器），是集抄片、真空干燥于一体的实验设备，适用于造纸科研院所及造纸厂研究与实验。它把纸浆抄成φ200的纸样，然后将该纸样在干燥器上干燥后再进行纸样物理强度的检验，鉴别纸浆原材料性能和打浆工艺规范，同时可完成纸浆的洗涤和浓缩实验，它的技术指标符合QB/T3703-1999（浆实验室纸页的制备+常规纸页成型器法）ISO 5269/2 & ISO 5269/3, NBR 14380/99, TAPPI T-205, DIN 54358, ZM V/8/76的要求。 
      结构特点：抄片和真空干燥一体；白水循环；电动上浆；压缩空气匀浆、手动匀浆、电动阀放水；真空泵辅助抽虑成型，还可抄取超厚纸样；超细纤维及超厚纸页成型辅助装置；喷淋装置；台面材料为不锈钢（304L），干燥体内装有弹性抽吸压平装置，纸样干燥厚度可达到10mm，真空泵自动防回油装置，外置水源快速接头；用户只需插上电源插头，连接水源快速接头，便可工作。
      采用三级离心式专用真空泵，该泵利用文丘里管原理和离心式真空技术产生高负压，体积小、结构紧凑、抽气量大；真空度高，使用过程不需要维护。可以在较为恶劣的环境下工作。

       三种干燥界面：
       1.镜面板干燥。

       2.胶面板干燥。 

       3.甘油胶囊干燥。
     参数：
      1. 试样直径： ?200mm
      2．真空泵真空度：-0.092~-0.098MPa 
      3. 真空压榨力：≈0.1MPa
      4．干燥温度：≤120℃ 
      5．干燥时间（定量30-80g/m2）：4-6分钟 
      6．加热功率：1.5KW×2 
      7．真空泵电机功率：2.2KW 
      8．外形尺寸：1800mm×710mm×1300mm 
      9. 台面材料为不锈钢（304L）。 
      10. 外加喷洒洗涤装置。
      11. 重量：295Kg
      12. 水源状况：需要连续水源
      配件：多孔搅拌器，成型滤网60目、80目，毛布伏压辊，标准伏压辊（304L），标准不锈钢伏压板。
      注：该款设备，纸样在真空干燥过程中，设备对纸样产生了大约0.1MPa的压榨压力，如果不需要压榨，可选择更换为不带压榨的真空干燥部件。根据用户需要可选择订做：对薄片无压榨力的干燥单元。

 PL6-D型纸样抄取器（可订购）：

针对不同的纸张，干燥器温度、干燥时间预先设置并可储存，以便下次使用。
预留上位机接口（PC机）以及打印机借口，可对该设备进行远程控制、记录。

 夹网片      

 毛布压伏辊（3Kg）

  标准伏压辊（13.3Kg）

真空干燥器上盖采用具有弹性的孔板，在真空抽力作用下完成对0~10mm厚纸张的压平真空干燥。

公司采用德国技术自主生产的三级离心式真空泵，保证了本机的高真空度，避免了市售真空泵在高温蒸汽环境下存在的，真空度低，使用寿命短等弊病。

为设备配备的直径为200mm的绷网器（更换成形网的专用工具）。

夹网片及网托架

网托架及真空抽虑室，压缩空气匀浆。

国标筛网目数及标准筛的网孔尺寸对照表

   PL6-C Handsheet Former(RAPID-KOETHEN)

The PL6-C handsheet former manufactured by our company is applicable to research and experiments in papermaking research institutes and paper mills. It copies pulp into a sample sheet, then puts the sample sheet on the water extractor for drying and then carries out the inspection of the physical intensity of the sample sheet to appraise the performance of the raw material of pulp and beating process specifications. Its technical indicators conform to China’s specified standard for papermaking physical inspection equipment. Vacuum-pumping is used for heating and drying in the drying part; the higher the degree of vacuum is, the drying speed is faster; the heating element has a long service life and is easier to replace for use of a heating plate; the temperature control system uses intelligent PID control, has functions of short circuit, wire break and over-temperature alarm and high precision in measurement and control and is safety and reliable; The vacuum system uses electromagnetic control, the machine is equipped with an oil return prevention system by which to avoid oil return caused by shutdown. The machine is easy to operate and convenient to use. The handsheet former makes pulp into sample sheets with a diameter of no more than φ200 and then dries the sample sheets by vacuum heating.
1. Diameter of sample sheet: ≤ 200mm
2. Vacuum degree of vacuum pump: 0.092-0.098MPa
3. Drying temperature: ≤105℃
4. Drying time (30-80g/m2 quantitative): 3-6 minutes
5. Heating power: 1.5KW×2; voltage: 220V
6. XMT616 intelligent PID temperature controller × 2
Working power supply: AC/DC 85-260V (50HZ/60HZ)
Thermal resistance: PT100 Operation environment: 0-±50oC: ≤85% RH
Contact capacity: AC 250V/3A Measurement accuracy: 0.2% F.S
7. DHC9J-L time totalizer
E2ROM is used to store data; the data can be stored for ten years and are displayed with a five-digit LED digital display.
The scope of the time totalizer is between 1s-9999.9h.
Power supply voltage: AC/DC 100V-240V
Power consumption: ≤3.5VA Time precision: ≤0.1%
8. Power of vacuum pump motor: 2.2KW Voltage: 380V
9. Power of jet self-priming stainless steel pump motor: 370W Voltage: 380V
10. Inflation valve for electromagnetic vacuum belt: current 0.048A Voltage 220V
11. Vacuum electromagnetic valve: ×2 Voltage: 220V
12. Electromagnetic valve for water drainage: voltage 220V
13. Mesa Material: stainless steel (304L)
14. Equipped with four standard floating press rollers (304L) with a weight of 13.3Kg each.
15. Coupled with a spraying and washing device.
16. Outline dimensions: 1800mm×720mm×1430mm .