发布需求
江苏 常州市| 品牌：昊升 | 产品类型：直流减速电机 | 型号：37JPG3429 |
| 额定功率：7W（W） | 额定电压：3-24（V） | 额定电流：0.657（A） |
| 额定转速：10-700（rpm） | 额定转矩：0.6（NM） | 外形尺寸：37*60（mm） |
| 产品认证：ROHS | 适用范围：保险柜 | 效率：30-50（%） |
产品用于各种精密设备.
1.Standard Operating Conditions:
标准运行条件
1-1.Rated Voltage 7.0 V DC constant
额定电压
1-2.Operating Voltage Range 3.5～9.0V DC at motor terminals
工作电压范围
1-3.Rated LOAd 3.0 Kgf.cm
额定负载
1-4.Excess Torque with-standing the max torque 20 Kgf.cm .
最大承受力矩
1-5.Direction of Rotation CW when viewed from output shaft side.
旋转方向 CW：从输出轴端看为顺时针
1-6.Motor Position All direction of protruded shaft
摆放位置 伸出轴的任意方向
1-7.Operating Temperature Range -5℃～+50℃
工作温度范围
2.Measuring Conditions:
测量条件
2-1.Motor Position Horizontally or Vertical
电机位置 水平或垂直。
2-2.Power Supply Regulated power supply which assures
电 源 unquestionable measurement
经过调节的直流电源以确保无问题测量。
2-3.Environment Temperature and Humidity
环境温度与相对湿度
The test is made in principle at theTemperaturebetween 10℃and30℃,and at relative Humiditybetween 30%and95%,Ifthetestresultisquestionable, it shall be judged from the test madeat JIS Standard Testing Condition (20±2℃,65%±5%RH). 该试验原则上在温度为10℃~30℃之间、相对湿度在30%~95%之间进行。如果对试验结果有 疑问，则应根据JIS标准试验条件下（20±2℃,65%±5%相对湿度）进行的试验进行判断。 2-4.Unless otherwise specified,rated voltage to be applied. 除非特别注明，使用额定电压。 |
3. Electrical characteristics
电气参数
3-1.No-load Speed 29±15% rpm
空载转速
3-2.No-load Current 150 mA Max
空载电流
3-3.Rated Speed 25±15% rpm
额定转速
3-4.Rated Current 500 mA Max
额定电流
3-5.Stall Torque 18Kg.cm Min
堵转力矩
3-6.Insulation Resistance 10MΩ Min. at 250V DC meg.
绝缘电阻
3-7.Endurance Voltage 1 mA/s Max at 600V/AC.
耐电压
3-8.ReferenceCharacteristicCurve See spec No.：37JPG3429-22200-150
参考特性曲线
3. Electrical characteristics
电气参数
3-1.No-load Speed 29±15% rpm
空载转速
3-2.No-load Current 150 mA Max
空载电流
3-3.Rated Speed 25±15% rpm
额定转速
3-4.Rated Current 500 mA Max
额定电流
3-5.Stall Torque 18Kg.cm Min
堵转力矩
3-6.Insulation Resistance 10MΩ Min. at 250V DC meg.
绝缘电阻
3-7.Endurance Voltage 1 mA/s Max at 600V/AC.
耐电压
3-8.ReferenceCharacteristicCurve See spec No.：37JPG3429-22200-150
参考特性曲线
4.Mechanical Structure and Character:
机械特性
4-1.Appearance No remarkable deformation and/or superficial defects.
外 观 表面无明显变形或缺陷。
4-2.Dimension AsperdimensionaldrawingNo.：37JPG3429-22200-150
外形图 符合尺寸图纸No.：37JPG3429-22200-150
4-3.Weights 180g (Approx)
重 量
4-4.Shaft End Play 0.5mm Max
轴端间隙
4-5.Mechanical Noise 55dB Max
机械噪音 Mechanical noise under No-load at Rated Voltage
(Back ground noise to be 29dB (A)max).
额定电压无负载时的机械噪音。 (背景噪音最大为30dB (A))
4-6.Vibration To be set up with mutual consent.
振 动 达到双方同意的标准。
5. Motor life test:
寿命试验
5-2.Voltage 7.0 V DC
电 压
5-3.Load 3.0 Kgf.cm
负 载
5-4.Environment 25℃±5℃/ 65%±20%RH
测试环境
5-5.Duty Cycle As sketched below.
测试模式 连续运转
Life end defined as follows:
按如下状态确定寿命终结：
1) When current is over±30%
agAInst the initial figure.
电流与初始状态下的电流有±30%的差异。
2）When speed is beyond±30%
against the initial figure.
转速与初始状态下的转速有±30%的差异。
3) When motor is unquestionable
recognized as unusable.
电机被明显确认为不可使用。
5-6.Life Expectancy: 300 Hrs MIN
期望寿命
6. Storage
贮 存
6-1.Storage Temperature -20℃~ +70℃.
储存温度
6-2.Storage Relative Humidity 10%~90%.
储存湿度
6-3.Keep dry, avoid storing in high temperature、high humidity or corrosive gas environment.
保持干燥，避免放置在高温、潮湿及有腐蚀性气体的环境中。
7. CAUTIONS：
注意事项
7-1.Since the performance of the motor is affected by environmental temperature,
condition be give to keep it away from out of range.
环境温度条件对马达性能有极大影响，请在本技术指标范围内使用马达。
7-2.It is not allowed to operate in the high temperature with high humidity or in the
rust or in the circumstance where the substances generating a harmful gas such
as low molecular Siloxane, syan, formalin ,quick-dry glue or the corrosive gas such
as H2S, SO2, XO2, Cl, exist.
避免在高温、高湿及与腐蚀液体、气体接触。
7-3. Do not lock the motor shaft while the electric is on .
If lock state more than 1 minute would or resistor is heated up and may burnt
but not start fire.
请不要在马达运行时锁定电机轴。
若持续锁定超过1分钟，马达将发热甚至烧毁。
7-4. Do not give direct shock to the motor.
应避免直接碰撞马达。
免责声明：本文所用视频、图片、文字如涉及作品版权问题，请第一时间告知，我们将根据您提供的证明材料确认版权并立即删除内容。
