名称: | MPPT12V/24V-30A/20A/30A |
产品用途: | 太阳能系统专用 |
产品介绍:
MPPT30控制器是一种智能型,多用途太阳能充放电控制器。该系列产品使用订制的LCD显示屏,具有非常友好的操作界面;各控制参数可灵活设定,充分满足您的不同需求。
MPPT30具有如下特点:
1.MPPT功能:本控制器特点在于智能调节太阳能发电板的工作电压能跟踪太阳能板发出最大电流,使太阳能板始终工作在V-A特性曲线的最大功率点。比较普通太阳能控制器,对太阳能板发电功率的利用提高了10-30%;
2.形象的LCD图形符号,简洁的按键模式;
3.带自动温度补偿的智能型PWM充电方式;
4.可调节的从放电控制参数,可设置的负载工作模式;
5.蓄电池反向放电,欠压,反接保护等各种保护功能。
一:Product introduction
Solar LCD series a kind of intelligent, multi-purpose solar charge and discharge controller
LCD screen display |
BATtery reverse discharge protection |
Easy operation interface |
Battery reverse polarity protection |
MPPT+ PWM charging mode |
Battery under voltage protection |
Parameter user can reset |
OverlOAd, short-circuit protection |
A key to open and close the load |
Automatic temperature compensation function |
A key to restore the factory settings |
USB 5V charging (for 500mA) for mobile phone |
二: Installation Instructions
Installation
① Ready Qi installation tools and materials, and cable. Please matching suitable cable
② Ensure that the current density <4A/mm2 this will help to reduce the line pressure drop.
Recommended: 30A current 10mm2 Check whether the installation site,Comply with the relevant safety requirements, avoid
damp, dusty, there is easy
Inflammable, explosive and corrosive gases place to install using the controller
③ Install the controller fixed to the vertical plane, see Section V mounting aperture and hole spacing. In order to ensure a good controller cooling conditions, the controller on the bottom of each reserved 10cm space
|
④ As shown on the right wiring sequence: load, battery, solar
Battery plate is connected to the controller to be taken to ensure that the load, battery,
The polarity of the solar cell panel and controller
⑤ Before use: external temperature sensor probe into the left of the controller temperature probe interface probe placed in similar battery temperature. (Line extension must be built-in devices of the external temperature probe coextensive Otherwise, the controller will control parameters of the temperature compensation of the error
⑥ Warning: In order to prevent accidents from occurring, install: non-professionals can not be engaged in loading and unloading operations
三LCD operating interface description
1:LCD graphic symbol description
LOAD ON 1 H---23H Load control (1 hour --- 23 hours can be set) |
|
LOAD ON 24H 24 hour -is normally open state |
|
0h-light control mode, power supply load after dark, closed after daybreak the load 24h-represents a normal mode, in the case of no fault, the load is always in the power supply state. 1h ~ 23h-light control delay mode, after dark began to power the load, and delay to set the time to close the load. |
|
Charging current |
Discharge current |
Voltage charging station (can be set) |
Undervoltage protection voltage (can be set) |
Temperature display (around the probe) |
Undervoltage recovery voltage (can be set) |
2 Function keys:
: Toggle key |
“+”Set parameters: "plus" |
“-” Set parameters: "Minus" |
Manual switch load |
Long press and hold this button for 5 seconds to restore the factory settings |
|||
"&tiMES;" error or system fAIlure, click this button, you can troubleshoot or eliminate "x" |
3 Parameter settings (≥ 5 seconds keystrokes, parameters are saved automatically)
:PV OFF:88.8V→LOAD ON:24H→LOAD OFF:88.8V→LOAD ON:88.8V(Set order (automatic cycle) |
|
+ Parameters "+" setting |
- Parameters "-" setting |
This button can be "manually" open load or manually close the load. Long press and hold this button for 5 seconds to restore the factory settings "×" error or system failure, click this button, you can troubleshoot or eliminate "x"
|
四 Common fault with processing methods
Battery under-voltage protection |
Battery normal power supply
|
a) Undervoltage protection and handling: screen display as shown on the right indicates the battery voltage is below the undervoltage protection voltage, the controller has entered undervoltage
b) Retaining state, disconnect the load circuit. Using solar panels or charger to charge the battery when the accumulator
c) After the battery voltage reaches the undervoltage recovery voltage, the controller will restore power to the load, into normal working condition
1) Overload protection and processing methods:
The screen shown at right load circuit current is greater than the rated current or load short-circuit, overload state controller has entered. Reduce the load troubleshooting, press the button, restore power to the load
System fault |
o r Fault has ruled out |
2) To charging failure handling method
a) Solar energy to battery charging, if there is no correct configuration solar panels of power or exceed rated charging current, voltage, will appear charge fault, the checking and debugging, press the button, recoverability work.k
Charge fault |
Fault has ruled out |
3) Solar panels fault and processing:
a) 24 hours in the case of sun light, the controller is not charging, the solar energy is not connected or not connected correctly, check the solar panel to the connecting cable of the controller is open, troubleshooting, recoverability work.
No solar charge |
Are charging |
五 Parameter table
model Parameters |
MPPTM 30 |
model Parameters |
MPPT 30 |
|||
Rated working current |
30A |
Installation wire number |
≤7# AWG (10mm2) |
|||
Rated working voltage |
12V/24V |
Working temperature |
-10℃~60℃ |
|||
Solar panels voltage |
≤48V |
Storage temperature |
-30℃~70℃ |
|||
Float charging voltage(settable) |
13.8V/27.6V |
Humidity requirements |
≤90%,NO GEL |
|||
Low voltage protection(settable) |
10.7V/21.4V |
dimension |
||||
Low voltage recovery(settable) |
12.5V/25.0V |
Mounting hole spacing |
60 mm×178 mm --Φ5 |
|||
No-load loss |
≤15mA |
weight |
≤460g |
|||
Loop pressure drop |
≤160mV |
Temperature compensation |
-4mV/Cell/℃ |
|||
Charging mode |
MPPT+PWM mode |
免责声明:本文所用视频、图片、文字如涉及作品版权问题,请第一时间告知,我们将根据您提供的证明材料确认版权并立即删除内容。