1-4．轴承Bearing

含油轴承Sleeve bearing

2．电气特性Electrical characteristics (在通风及额定电压条件下in free AIr at rated voltage)

2-1．额定电压  Rated voltage

12V

2-2．额定电流  Rated current

0.25A（MAX0.28A）

2-3．额定输入功率Rated input power

3.00W（MAX3.36W）

3．效率Efficiency

3-1．风扇转数Rated speed

3300±10%RPM.

3-2．最大风量Maximum air flow

35CFM

3-3．最大静压Maximum static air pressure

0.15inch-H2O

4．特性规格Characteristics

4-1．运转方向Directing of  rotation

CW（贴标签面看叶片顺时针方向运转）

4-2．操作电压Operating voltage range

6V~12V

4-3．起动电压Starting voltage

6 V(ON/OFF)

4-4．锁定电流Locked current

无锁定保护功能

4-5．操作温度Operating temperature

-10℃~+70℃

4-6．储存温度Storage temperature

-30℃~+85℃

4-7．环境湿度Environment humidity

10%℃(RH) 45℃for24 hours & (RH)45℃for24 hours

4-8．绝缘阻抗强度Insulation resistance

在本体与两条导线间加500V直流电压之绝缘阻抗在10MΩ

以上

At least10MΩ at 500VDC between housing and both leadwires.

4-9．绝缘耐压强度Dielectric strength

必须能抵抗在本体与两线间加500V交流电压1分钟lmA。

Withstand 500 VAC 1 minute 1mA between housing and both lead

 wires.

4-10．预期寿命（MTBF）：指在额定电压及正常温度，湿度条件下连续运转

      Life expectance: continuous operation at rated voltage and normal temperature & humidity

4-10-1．含油轴承预期寿命：20000小时

        Sleeve bearing life expectance: 20000h

4-11端子抗拉强度Tensile strength of

connector

端子以1公斤的拉力拉扯15秒不会脱落

Connector will not be any broken at 1kg for 15seconds per piece.

4-12.噪音分贝Acoustic sound level

30dB (Max)

4-12-1.噪音测试说明Acoustic sound level test descriptions

以额定电压在噪音实验室中测试（背景噪音18分贝以内）

At rated voltage in sound proofroom

Background noise:18dB                           

                                                 悬吊Suspension                

                                                                    1m           麦克风感应器

                                                                                    MIC.

                                   通风状态                           (对准风扇中心)         

                                    Free air                         (Alm to center of the fan)

                                                   风扇Fan

5.特性定义Characteristics

5-1.  额定电流＆额定转速＆额定操作功率，须在额定电压下；马达连续转５分钟达到规格下限，10

分钟达到正常值

Rated current, rated speed, and rated input power shall reach bottom line of specification after 5 minutes

Continuous rotation at rated voltage and reach standard specification after 10 minutes continuous voltage.

5-2.起动电压是指突然通电后能够使风扇起动之最低电压

Starting voltage is the least voltage that enables to start the fan by sudden power on

5-3.轴向间隙Shaft end play

马达水平方向放置0.5~0.8mm

With dial-gauge and so on.

5-4.轴垂直度

Perpendicularity of shaft

安装平面为基准测试90±0.5º

Measuring based on the mounting plate.

5-5.轴长同心度

Shaft deflection

从安装平面3mm测试<20µmor less

At the point 3.0mm from the mounting plate.

6．安全规格Safety

CE  TUV

7．原材料Material

主要元件

Major components

材质或型式

Material & Specification

外框

Fan Frame

PBT 70% +Fiber 30%

扇叶

Fan blade

PBT 70% +Fiber 30%

轴心

Stator core

不锈钢

Stainless steel

(SUS420J2)

轴承

Bearing

滚珠轴承或含油铜轴承

Ball bearing or sleeve bearing

(Cu+GLY)-2100

橡胶磁铁

Rubber magnet

铁锶粉末化合物

Strontium ferrite

(BQB14W)

矽钢片

Silicon steel strip

(H23) (H-18)

漆包线

Enameled copper

wires

去膜直径0.04~0.20

Material & specification

0.04~0.20mm

印刷线路板

Printed CircuitBOArd

单层印刷线路板

Wiring printed single layer board

电源线

Lead wires

聚乙烯氯化物包铜线

Polyvinyl Chloride enameled

Copper wirer (AWG#26)

贴纸  Label

多元脂

Polyester

端子接头

Connector housing

2.5P端子

8. 出货检验程序Product inspection procedure

         本公司出货检验程序均依照下列步骤实施Inspection procedures below are extremely followed.

8-1.100%生产线上电性;死角,扇叶拉拨.

     100%Electric;rotating,dead spot,fan blade fasten, and primary noise test on production line.

8-2.100%生产线上以示波器作正常电流波形筛检

     100% Current wave test with scope on production line.

8-3.100%以手敲击测试及静音室异音过滤

 100% Strick test by hand and noise filter in quiet room.

8-4.10cm落地试验依MIL-STD-105E作抽样

 10cm drop test at random in accordance with MIL-STD-105E standard

8-5出货抽样检验依MIL-STD-105E作允退判定

    Random inspection in accordance with MIL-STD-105E standard.

8-6允退标准如下P

    加严Critical AQL:0.4           正常Major AQL:0.65              宽松Minor AQL:1.0