本厂成立于1994年,专门生产袖珍式手动缝纫机,现在有独立的品牌和专利技术,凡是本厂出的产品,如遇有质量问题1月内包退,半年内包修.如客户需要详细的资料可通过我们联系索取.本厂现有2-3种商标,6-8份专利,本厂忠诚为每一个客户服务.

操作说明

1.持机：用右手四指托住机座，大拇指自然的放在机身上盖顶端，平稳的持住整机。如图(1)所示。
1.Holding:suppouting the botton of the machine with the four fingers of your right hand and them putting your thumb
 on the top of the machine for holding the machine tightly.(fig 1)
2.穿线：如图（1）将线轴一的线轻轻拉出。穿过引线圈A，然后引入夹线调节片B。在穿过引线圈C。
引过的线头暂时放在机针旁，另将穿线器从机针前面（向机身结合部）穿过机针孔，再将线头引入穿线器小孔中，退出穿线器拉出线头约2-3公分压线板压住即可待用。（见图1）
2.Threading:(fig 1)drawing the lisle softly from the bobbin and threading it from winding A,and the put it in the tension controller B.Then threading it through the winding C.Putting the top of the lisle beside the needle,and then threading the lisle through the needle by using the threader.2-3 centimetre.(fig 1)
3.放布：用右手食指抬起压板，将准备好待缝的织物（厚度不超过0.8毫米）平整放入压板下，轻轻放回压板压住织物；（见图2）
3.Life up the clothe fastening plate with reght forefinger and putting the cloth(less thean 0.8mm gauge)under the fastening plate,and then setting down the fastening plate.(fig 2)
4.缝纫操作：用左手持织物，右手大拇指轻轻的迅速地下压上盖顶端压到底后，大拇指上台再下压，如此反复，送布机构地洞将被缝物向左送出。持机右手逐渐右移，左手持布配合缝纫节奏轻轻将被缝物向左移动，直至缝纫结束：如（图2）
4.Pressing the top of the maching up and down and do over,then the right hand should move to right step by step and let left hand hold the cloth the controll the direction.(fig 2)
5.本机能自动进布和调节针脚间的松紧，图1（b）螺母调节。
5.You can adjust the bolt for the optimal habitus,adjust nut fig 1(b).
6.换线团：如换用大线团，可将备用的接长杆与线筒轴连接，套入大线团。然后重新穿线，调整线的松紧后进缝制，（见图3）；使用50#-90#棉线可合成线效果最好；
6.Drawing prolate distaff and thread spindle if you want to change an big clew.After threading agAIn and readjusting the tight and loose of lisle,you can sewing again.50#-90#.(fig 3)
7.换针：松开固定螺丝，取出断针。照（图4）所示装上新针，注意要将针的平整面对正固定螺丝，不可装反。针型DHX-14.
7.Loose the setscrew with ascrewdriver and take off the old needle.Notice to let the flat part needle face the invariant setscrew.Correct direction and position of needle.DHX-14(fig 4)